Continuation
I decided to add a third installment to my blog on Market Surveillance and the revised Machinery Directive 2006/42/EC. As noted several times the impetus for these comments has been driven by serving as legal expert in a lawsuit involving a CE Marked machine that has killed one worker and injured another worker who will need 24 hour care for the rest of his life. These accidents involved the same machine model in two separate incidents in two different countries.
While the Technical File was a junk file that did not comply with the requirements of the Machinery Directive, the contents of the file and the pathetic state of compliance was unknown until the first accident occurred and the file was turned over to the Health and Safety Executive (HSE) in the UK. In reality, the pathetic state of compliance is still unknown because, as noted in the previous blog, HSE investigates workplace accidents and BIS (Department for Business Innovation and Skills) the Competent UK Authority that oversees CE Marking for the Machinery Directive has not received the HSE investigation report. Meanwhile, the non-compliant machines are still on the market.
CE Marking Litigation And Its Future
I only reiterate these facts because in the past two weeks, I have received calls from two new clients involved in lawsuits in the US concerning CE Marking for the Machinery Directive. I anticipate more in the future. There are several reasons for this increased litigation activity, among them:
- CE Marking safety requirements and standards for machines have grown in number and sophistication since the Machinery Directive was first published on 14 June 1989.
- Following the Vienna and Dresden agreements between the EU Standards Bodies (CEN and CENELEC) with ISO and IEC respectively (to avoid duplicating standards writing efforts) these new international standards writing activities automatically include the participation of ANSI (American National Standards Institute) in drafting ISO & IEC standards resulting in EN ISO and EN IEC standards that are also American National Standards, recognized by US Courts of Law. In sum, EN standards are rapidly becoming American standards.
- US Federal Courts offer a litigation venue for product liability, Breach of Warranty and Breach of Contract lawsuits concerning CE Marking between US Citizens and US machinery manufacturers, US Citizens and EU machinery manufacturers and EU Citizens and US machinery manufacturers.
- The oft cited 2002 Minnesota case where a California Packaging Machinery Manufacturer sold a less safe machine in the US injuring a worker who will require 24 hour care for the rest of his life (it didn’t have a laser light curtain to turn off the machine when a worker entered the area of machinery activity), but sold safer CE Marked machines with laser light curtains in the EU for 6 years because of the Machinery Directive safety requirements, resulted in a $35 million punitive damages award (the manufacturer knew how to make a safer machine and chose not to do so). This means that US manufacturers who follow the same path of selling less safe machines in the US and safer machines in the EU and EU manufacturers who sell non CE Marked less safe machines in the US can expect a similar result in US Courts. It is a whole new area of litigation for American trial attorneys.
- Just as trial attorneys can ask for ISO 9001 records and documents that are relevant to a product liability lawsuit in the US and EU, they can now ask for Machinery Directive Technical File records and documents in discovery in Product Liability, Breach of Warranty and Breach of Contract lawsuits. The fact that these records and documents may belong to a European manufacturer is irrelevant. Whether the EU manufacturer is suing or being sued the cause of action arises from doing business in the US, making the litigants subject to US Courts and US rules of civil procedure.
These are a few of the legal nuances for US Courts of Law brought about by the evolution of the Machinery Directive and its supporting standards writing activities.
The Response of EU Competent Authorities
In future blogs I will spend more time examining the substance of Decision No 768/2008/EC of the European Parliament and the Council of 9 July 2008 On a Common Framework For the Marketing Of Products and Repealing Council Decision 93/465/EEC. In the preceding two blogs (July 30 & August 15) and this blog, however, I have concentrated on administrative issues not touched on in Decision No 768/2008/EC that I believe are critical to the success of effective Market Surveillance as it relates to the Machinery Directive.
In the section titled “A View Thoughts” in the preceding August 15 blog, my Fifth recommendation was, “once a complaint or accident involving a CE Marked machine is recorded by a Competent Authority, a checklist protocol should be developed utilizing Annex VII of Machinery Directive 2006/42/EC to determine if all the elements of a Technical File contained in A. Points 1,2 & 3 are compliant. Listed below are those points
1. The technical files shall comprise the following:
(a) a construction file including:
-- a general description of the machinery,
-- the overall drawing of the machinery and drawings of the control circuits, as well as the pertinent descriptions and explanations necessary for understanding the operation of the machinery,
-- full detailed drawings, accompanied by any calculation notes, test results, certificates, etc., required to check the conformity of the machinery with the essential health and safety requirements,
-- the documentation on risk assessment demonstrating the procedure followed, including:
(i) a list of the essential health and safety requirements which apply to the machinery,
(ii) the description of the protective measures implemented to eliminate identified hazards or to reduce risks, when appropriate, the indication of the residual risks associated with machinery,
-- the standards and other technical specifications used, including the essential health and safety requirements covered by these standards,
-- any technical report giving the results of the tests carried out either by the manufacturer or by a body chosen by the manufacturer or his authorized representative,
-- a copy of the instructions for the machinery,
-- where appropriate, the declaration of incorporation for included partly completed machinery and the relevant assembly instructions for such machinery,
-- a copy of the EC declaration of conformity.
(b) for series manufacture, the internal measures that will be implemented to ensure that the machinery remains in conformity with the provisions of the Directive.
The manufacturer must carry out necessary research and tests on components, fittings or the completed machinery to determine whether by its design or construction it is capable of being assembled and put into service safely. The relevant reports and results shall be included in the technical file.
2. The Technical file referred to in point 1 must be made available to the competent authorities of the Member States for at least 10 years following the date of manufacture of machinery or, in the case of series manufacture, for the last unit produced. (Emphasis added)
The technical file does not have to be located in the territory of the Community, nor does it have to be permanently available in material form. However, it must be capable of being assembled and made available within a period of time commensurate with its complexity by the person designated in the EC declaration of conformity. (I suggested 48 hours, similar to the Medical Devices Directives)
The Technical file does not have to include detailed plans or any other specific information as regards the subassemblies used for the manufacture of the machinery unless a knowledge of them is a central for verification of conformity with the essential health and safety requirements.
3. Failure to present the technical file in response to a duly reasoned request by the competent national authorities may constitute sufficient grounds for doubting the conformity of the machinery in question with the essential health and safety requirements. (Emphasis added)
Conclusion
As noted in the two previous blogs, I think these types of steps are essential for effective Market Surveillance for the revised Machinery Directive 2004/42/EC. I also noted previously that I would like to work with European manufacturers and companies on steps to reduce their liability exposure in the US market. It seems to fit the European philosophical approach to product safety and would help EU firms concerned about the litigious nature about the US marketplace. If anyone is interested in exploring these topics further, please contact me at jameskolka@gmail.com or jim@jameskolka.com.
Comments